Ace
$799.00
The PHRED instruments Ace guitar is a neck through double cut-away guitar that gets its inspiration from Bob Weir’s Cowboy Fancy guitar. The body features a humbucker-single-humbucker setup, with a split coil switch for the humbuckers and discrete on-off toggles for each pickup. Our Ace guitar is professionally setup with low action and D’Addario 10-46 strings, and the frets are leveled and milled here at our shop in California for a nice smooth and clean feel all around.
Order fulfillment is currently estimated at 12 months because we are working on fulfilling a backlog of pre-orders.
-
Body
The body features a humbucker-single-humbucker setup, with a split coil switch for the humbuckers and discrete on-off toggles for each pickup. There is one master volume and 2 tone knobs, allowing you to dial in tone that goes from dark and muddy to crisp and bright. Additionally there is a 3-band EQ that can be activated to further dial in your sound. There is one 1/4″ output jacks on the top of the body. On the back of the guitar, there is a large and accessible electronics cavity and a 9V battery box that powers the internal EQ.
Neck
The 5-play neck-through guitar is comprise of maple and walnut. The back of the neck contour is a C-shape that feels somewhere in between a strat and an LP neck, not too thin, and not too chunky either. The 22 fret ebony fingerboard has medium jumbo frets which are leveled and milled here at our shop in California for a nice smooth feel along the edge of the fretboard. The fretboard features a 12 inch radius which is a nice balance for playing chords up and down the fretboard. Topping off the fretboard is a custom vine pearloid inlay. At the top of the neck, you’ll find a bone nut for good sustain, and white binding all around the fingerboard for a uniform look and feel. The tilt-back 3+3 headstock shape features white binding as well. Under the fretboard is the adjustable double-expanding truss rod, keeping the neck stable in any climate.
Only logged in customers who have purchased this product may leave a review.
13-point Setup
Our 13-point setup and inspection ensures that every PHRED Instruments guitar we ship is professionally setup and ready to play when it’s delivered to you. Setup will include string-height adjustment, intonation, electronics inspection, and the frets are leveled, crowned, and polished, as outlined below.
Fretwork and Fingerboard
1. Debur Fret Edges
This process involves filing the edges of each fret such that the edge of the fretboard feels smooth as you play up and down the neck.
2. Level Frets
Leveling all the frets ensures that you can play at low string action and with clear and articulated notes on each fret.
3. Crown Frets
After leveling the frets, they are crowned. Crowning frets is a process by which the frets are rounded slightly at the top. This makes the frets feel nice and smooth all around, ensures smooth bends, and also makes it easy to slide up and down the fretboard.
4. Polish Frets
After crowning the frets, polishing makes them shine brightly. Polishing them also makes them even more smooth to the touch.
5. Condition the fingerboard
The fretboard wood is cleaned and conditioned using fretboard oil.
Setup
6. Adjust Truss Rod
The truss rod should be adjusted such that the neck is slightly concave.
7. Adjust Nut
The nut height is adjusted to the fingerboard, and the string slots are filed to a perfect height and width for the strings we install
8. Adjust the Bridge Height
As a part of setting the string action, the bridge height is adjusted to our standard measurement of 1.75mm above the 12th fret on the low E string, and 1.5mm above the 12th fret on the high E string. We leave a little bit of room if you want to adjust the bridge a bit lower than that.
9. Adjust the Bridge Saddles
Intonation is set by adjusting the bridge saddles. We tune up and stretch a fresh set of strings, and then adjust the bridge saddle position until the harmonic at the 12th fret compared to the note at the 12th fret.
Pickups
10. Adjust pickup height
The height of the pickup is adjusted such that the perceived volume is consistent between each of the pickups installed on the guitar.
Electronics
11. Inspect and test electronics
Whether you upgrade to our USA wiring option or go with the stock wiring and electronics, we are going to make sure all the electronics work properly prior to shipping. For guitars that have an OBEL jack, we wire it Tip=Send, Ring=Return.
Strings
12. Install D’Addario 10-46 gauge strings
We install D’Addario EXL 10-46 gauge strings on all guitars. If you prefer a different brand or string gauge, contact us and we can accommodate other brands and string gauges, and adjust the setup accordingly to the strings that you prefer to use.
Guitar Body & Hardware
13. Clean and polish the guitar body and hardware
Just before we package up a guitar for shipping, we clean and polish your guitar using StewMac Guitar Polish to make it shine.
Contact Us
Body Style | Neck Through |
Body Wood | North American Ash |
Body Binding | Colorful Pearloid |
Scale Length | 25 1/2" |
Frets | 22 Medium Jumbo |
Neck Wood | 5-ply, Maple & Walnut |
Neck Binding | White with Black Dots |
Fretboard Wood | Ebony |
Fretboard Inlays | Pearloid Designs |
Fretboard Radius | 12 inch |
Neck Stabilization | Double-Expanding Truss Rod |
Nut Width | 1 11/16" (43mm) |
Nut Material | Bone |
Headstock Binding | Colorful Pearloid |
Tuning Machines | Unbranded Stock Tuners |
Neck Pickup | Humbucker (4-wire) |
Neck Pickup Color | White |
Middle Pickup | Single Coil (2-wire) |
Middle Pickup Color | Black |
Bridge Pickup | Humbucker (4-wire) |
Bridge Pickup Color | Black |
Bridge Style | Hardtail Bridge |
Volume Knob(s) | 2 Volume Knobs (Main Volume and EQ Level Volume) |
Tone Knob(s) | 1 Tone Knob |
Pickup Toggle | Discrete On/Off Toggles |
Neck Pickup Toggle Switch | Mini Toggle (Series/Split Coil) |
Bridge Pickup Toggle Switch | Mini Toggle (Series/Split Coil) |
Control Knobs and Toggles Notes | Neck and Bridge Series/Split Coil Toggle is combined on one mini toggle |
Pre-amp / Buffer | 3-Band EQ (Requires 9V Battery) |
Battery Box | Yes (9V Battery Included) |
Output Jack(s) | 1 Standard Mono Guitar Output Jack |
Output Jack(s) Notes | Plugging a guitar cable into the mono guitar output jack powers on the 3-Band EQ. |
Guitar Strings | D'Addario EXL 110 Nickel Wound 10-46 |
Guitar Dimensions | TBD |
Guitar Weight | TBD |
Reviews
There are no reviews yet.